It saves me counting lots of stitches in one go (I frequently make mistakes or miss one doing this) and I am confident when I start knitting that I have the right number. On my first row I then remove the markers when I come to them. I continue doing this until all stitches are cast on. Learn how to do the long-tail cast on, a popular method of casting on in knitting, plus learn the best ways to estimate the length of your tail for least yarn wasted. I then cast on another 50 stitches, count from the previous stitch marker and place another marker. It might look a little weird at first, but once you get the hang of it, youll be knitting. I will often cast on 50 stitches, count to makes sure the number is correct, then place a stitch marker. The easiest and quickest way of casting on is the longtail cast on. My other trick when casting on a lot of stitches is to use stitch markers to help me count. Make sure that the yarn tail is sitting towards you. Place the slip knot on needle and hold it in your right hand. You start by making a slip knot (we've got a tutorial for that too). A great technique when you want to make something stretchy such as a scarf or a hat. I am then able to measure out 150 inches, make a slip knot here and start casting on. Here's how to cast on using the longtail cast on technique. I then add 8 inches for a tail taking to the total yarn needed for my Long Tail to: Then to work out the final yardage I times the answer above by the number of inches used in my 20 stitches (7 inches in this example) by the answer above: All subsequent stitches have a double wrap.Finally I calculate how much yarn will be needed in the final cast on by dividing the number of stitches needed for my cast-on by 20 (the number in step 1). With this cast-on the initial stitch will be a single stitch created by the slip knot. Hold the tail yarn in your left thumb and hold the working yarn in your left index finger. Slide the slipknot into one of the knitting needle. Make a slipknot in the middle of the loose yarn. Do what works for your tension: Cast on 20 stitches and unravel. Drop the loop from your finger and tighten the loop. Pull about 20 inches (50.8 cm) from the ball of yarn. I usually give myself 12' of tail for every 20 stitches, more generously if it's bulky yarn.Draw the needle back through the loop on your finger in a knit-wise motion,.With the working yarn and your right hand, wrap the yarn twice around the needle.Insert the knitting needle through the loop on your finger as if to knit.Wrap the tail end of the yarn around your left-hand index finger in the same manner as doing a backwards loop cast-on. The Long-Tail Cast On is a two-strand cast on and is many a knitter’s preferred method of casting on because it’s strong, elastic, and quite versatile. The second method I’ll demonstrate is more like knitting the stitches off of your finger. Long-Tail Cast On, as well as two of our favorites for beginning 1×1 ribbed fabrics: the Ribbed Cable Cast On and the Tubular Cast On. Drop the loop from your thumb and tighten the loop.Įach double-wrapped stitch is considered one cast-on stitch.Draw the needle back out through the thumb loop,.Then wrap the yarn that leads to the finger twice around the needle.Create the initial loop as usual by inserting the needle through the thumb loop.The tail goes over my thumb and the working yarn goes over my index finger.I’ll begin by demonstrating the sling-shot method of casting on. After you become more expert, you may wish to find out more about the other methods. We recommend learning the knitting cast-on as your first method because it is simple and leaves an edge that stretches well. Hold your yarn and needle the way you usually do for a long tail cast-on. the long-tail cast-on, the cable cast-on, the double-knitted cast-on and the crochet edge cast-on. You should be able to adapt it to your usual method. In this tutorial I’ll demonstrate two different ways of doing the double-wrap long tail cast-on. There are multiple ways of working a conventional long tail cast on. So if the finished edge is meant to be 10” wide, then begin with a tail about 40” long.īegin with a slip knot and place it on your needle. You’ll need a tail about four times longer than the width of the cast-on edge. If you’re already familiar with the long tail cast-on then this will look familiar to you. It’s worked like a Long Tail Cast-On with a double wrap so that you can begin working double garter stitch right from the cast on. I’ve developed a cast on that works beautifully with the double garter stitch. Long-Tail Cast-On Make a slipknot on the needle and hold the needle in your. The whole cowl is worked in double garter stitch. 5 4 3 2 1 Casting On Stitches Every knitting project begins by putting a. This is the length of tail needed to cast on 10 stitches. Measure the length of yarn between your hands. Draw your hands apart to unravel stitches. With one hand, hold end of tail close to last stitch cast on. This is the Breakers cowl from my book, Tempest. Sampling Cast on 10 stitches using long-tail cast on method.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |